All models have the same bright red 9/16" tall LED display.
Tachulator SFM Digital Tachometer: NA
Custom die cast aluminum enclosure model by MKC Tools. 3 5/8" sq. x 1 5/8" deep.
RPM plus surface feet per minute calculator.
Includes sensor, power transformer, contol knob, instructions, sensor disk printout and heat shrink.
You also get tech support if needed to make your installation go smooth and easy.
Metric option available at no charge. OptionalMetric/Emperial switch available below.
Trexon SFM Tachulator black diecast enclosure: $119.95
|
Digital Tachometer only (NO SFM): $99.95
Custom die cast aluminum enclosure model by MKC Tools.
Measures 3 5/8" sq. x 1 5/8" deep.
Digital tachometer only, no SFM feature.
Includes sensor, power transformer, instructions, sensor target disk printout and heat shrink
for the sensor wiring plus tech support if needed to make your installation go smooth and easy.
Trexon digital tachometer MKC custom diecast enclosure: $99.95
|
Trexon Tachulator Digital Tachometer w/SFM module only with sensor: $69.95
This the Tachulator SFM module only for mounting in your DRO or other enclosure. Made for flush mounting to
enclosure inside front with all connections and controls on the back of the board for easy access.
The board measures 2.90" x 2.44" x .60" excluding control shaft. You can use any 9-11 volt transformer.
See the mounting examples.
Includes sensor, instructions, sensor disk printout and tech support.
Transformers, extra sensors and mounting kits available below.
Trexon Tachulator module only: $69.95
|
Trexon Digital Tachometer module only and sensor (no SFM feature): $59.95
This model is great for mounting in your DRO or other enclosure. Made for flush mounting to
inside of enclosure front with all connections and controls on the back.
The board measures 2.90" x 2.44" x .60". You can use any 9 to 11 volt transformer.
See the mounting examples.
Transformers, extra sensors and mounting kits available below.
Includes sensor, instructions, sensor disk printout and tech support.
Trexon Digital Tachometer module: $59.95
|
Extra optical sensors --
Available only to purchasers of tachometers from MKC Tools.
For replacement or extra sensors for multiple function machines or to use
one tachometer on different machines. Multiple sensors can be wired and
switched to work with one tachometer.
Extra Sensor for Tachulator or Digital Tachometer: $8.75
|
In-panel installation kit for Tachulator
Includes red display filter material pre drilled, aluminum knob, function
label, 18" heat shrink for sensor wiring, stainless screws,
lock washers and nuts,and nylon spacers. This kit contains everything you will need
to mount the Tachulator board in your DRO or other control panel or enclosure. The
tachometer module comes with an actual size print of the board which can be used
as a drilling templete.
In-panel installation kit for Tachulator: $9.95
|
In-panel installation kit for digital tachometer (no knob)
Includes red display filter material pre drilled, 18" heat shrink for sensor wiring,
stainless screws, lock washers and nuts, and nylon
spacers. This kit contains everything you will need to mount
the digital tachometer board in your DRO or other control panel or enclosure. The
tachometer module comes with an actual size print of the board which can be used
as a drilling templete.
Available only to purchasers of tachometers from MKC Tools.
In-panel installation kit for digital tachometer (no knob or label): $7.95
|
Power transformer 9 volt 300 ma with right angle plug
Perfect for powering the Tachulator or Digital tachometer.
The right angle plug allows a clean,
no holes visible installation with wiring through the top, bottom, side or rear of your enclosure.
Available only to purchasers of tachometers from MKC Tools.
Power transformer 9 volt 300 ma with right angle plug: $9.95
|
12 Volt to 9 volt step down power for running the Tachulator or
Digital tachometer on 12 volt auto type systems. The 13.8 volts
normally maintained in auto system is to high for the tachs and
will overheat and damage the board.
Available only to purchasers of tachometers from MKC Tools.
12 Volt to 9 Volt step down: $9.75
|
Metric/Imperial switch installed in die cast model
Available only to purchasers of Tachulator in die cast enclosure.
Instantly switch from metric to imperial modes by simply throwing the switch.
Imperial: input in inches, output in surface feet per minute
Metric: input in mm, output in meters per minute
Metric/Imperial switch installed in die cast model: $28.50
|
Engine turning and other custom mounting options available. Just contact me with details for
a quote.
Engine turning or paint added to diecast models: $19.50
|
